Ru
    En
    Primer-enamel 3 in 1 FERROCOLOR
    premium
    Colors
    Features
    Buy
    Primer-enamel 3b1 FERROCOLOR premium is a ready–to-use glossy and semi-matte weather-resistant alkyd primer-enamel designed for painting metal, wood and other surfaces exposed to atmospheric influences, as well as for finishing works inside residential and industrial premises.

    Technological properties of the soil-enamel 3b1 FERROCOLOR premium

    • Время высыхания
      at a temperature of (20±5)°C and relative humidity (65±5)% to the degree of 3 (for peeling) - no more than 3 hours, complete drying - no more than 6 hours,
      at a temperature of (105 ± 5)°With complete drying no more than 35 minutes.
    • Temperature of application, application
      it is recommended to apply primer-enamel at a temperature from +5 ° C to +35 ° C and a relative humidity of no more than 85%,
      the temperature range of operation of finished products from -45 ° C to +60 ° C.
    • Application conditions
      Primer-enamel 3b1 FERROCOLOR is a ready–to-use glossy and semi-matte weather-resistant alkyd primer-enamel designed for painting metal, wood and other surfaces exposed to atmospheric influences, as well as for finishing works inside residential and industrial premises. The surface intended for painting must be cleaned of dust, rust and other contaminants and degreased with a solvent. If necessary, the surface to be painted can be sanded, leveled with putty and sanded. When applying the primer enamel to the old coating, the latter must be sanded and washed with a solvent.
    • Expenditure
      at least 80 - 150 g/m2 is used per layer,
      1 kg of primer-enamel is used for processing up to 12 m2 of surface,
      the consumption depends on the level of surface preparation, as well as the method of applying the primer.
    • Shelf life, storage conditions
      the guaranteed shelf life of the primer enamel is 6 months from the date of manufacture. Storage conditions. Primer-enamel should be stored packed in closed warehouses at ambient temperatures from -40 ° C to + 40 ° C.
    • Conditional viscosity
      according to the VZ-246 type viscometer with a nozzle diameter of 4 mm, at a temperature of (20.0 ± 0.5) °C - not less than 150 - 250 s .
    • Degree of dilution
      no more than 25%.
    • Degree of grinding
      no more than 40 microns.
    • Mass fraction of non-volatile substances
      at least 50%.
    • Coating hardness
      according to a pendulum device of the type TML I (pendulum A) - at least 0.1 relative units.
    • Elasticity of the film during bending
      not more than 1 mm.
    • Impact strength of the coating
      according to the device type U-1 - not less than 40 cm.
    • Adhesion
      1 point.
    • Film durability
      to static water exposure - at least 2 hours.

    Colour

      Scope of application

      • For painting metal, wood and other surfaces
        Primer-enamel 3b1 FERROCOLOR is a ready–to-use glossy and semi-matte weather-resistant alkyd primer-enamel designed for painting metal, wood and other surfaces exposed to atmospheric influences, as well as for finishing works inside residential and industrial premises.

      Method of application

      • Primer-enamel 3 in 1 FERROCOLOR classic can be applied by any means: spray, brush, roller, dipping, jet pouring
        The work must be carried out in ventilated areas using personal protective equipment for the skin, respiratory organs, eyes and face.

        The preparation of the working composition consists in thorough mixing. If necessary, it is allowed to add a solvent (P4, xylene or white spirit) in an amount of no more than 20%. The working composition not used during the shift should be filled with a small amount of solvent and tightly closed with a factory lid to prevent moisture ingress, gel formation and increased viscosity during storage.

        The material can be applied at an air temperature from +5 °C to +35 °C and a relative humidity of up to 85%. It is not allowed to be applied on a wet or wet surface. The material should be applied in a uniform layer with a thickness of 30 to 80 microns, depending on the coating system used. The material is applied in 1-2 layers. The holding time before applying the second layer at a temperature of (20 ± 5) ° C should be at least 8 hours, but not more than 2 days. The thickness of a single–layer coating (on a dry layer) is no more than 30 microns. Approximate consumption rates per layer: from 80 g/m2.
      For delivery issues, contact the sales department:
      +7 (903) 885-79-76, +7 (910) 030-16-79

      E-mail:
      Sale@ferropolymer.ru