PF shipboard

Enamel PF FERROCOLOR shipboard

Enamel PF FERROCOLOR ship - ready-to-use glossy and semi-matte weather-resistant alkyd enamel is designed for painting metal, wood and other surfaces exposed to atmospheric influences, as well as for finishing works inside residential and industrial premises.

Technological properties of ship enamel PF FERROCOLOR

Drying time
at a temperature of (20±5)°C and relative humidity (65±5)% to the degree of 3 (on the chip) - no more than 12 hours, complete drying - no more than 24 hours,
at a temperature of (105 ± 5)°With complete drying no more than 35 minutes.

Temperature of application, application
it is recommended to apply enamel at a temperature from +5 ° C to +35 ° C and a relative humidity of no more than 85%,
the temperature range of operation of finished products is from -45 ° C to +60 ° C.

Application conditions
Enamel PF FERROCOLOR SHIP – ready-to-use glossy and semi-matte weather-resistant alkyd enamel is designed for painting metal, wood and other surfaces exposed to atmospheric influences, as well as for finishing works inside residential and industrial premises.

Expenditure
at least 80 - 150 g/m2 is used per layer,
1 kg of enamel is used for processing up to 12 m2 of surface,
the consumption depends on the level of surface preparation, as well as the method of applying the primer.

Shelf life, storage conditions
The warranty period of enamel storage is 6 months from the date of manufacture. Enamel should be stored packed in closed warehouses at ambient temperatures from -40 ° C to + 40 ° C.

Conditional viscosity
according to the VZ-246 type viscometer with a nozzle diameter of 4 mm, at a temperature of (20.0 ± 0.5) °S - at least 100 - 180 s .

Degree of dilution
no more than 25%.

Degree of grinding
no more than 25 microns.

Mass fraction of non-volatile substances
at least 50%.

Coating hardness
according to a pendulum device of the type TML I (pendulum A) - at least 0.1 relative units.

Elasticity of the film during bending
not more than 1 mm.

Impact strength of the coating
according to the device type U-1 - at least 50 cm.

Adhesion
1 point.

Film durability
to the static effect of water - at least 48 hours,
to the static effect of gasoline and solvents - at least 48 hours,
to the static effect of salt solutions (3% sodium chloride solution) - at least 96 hours.

Colour

Scope of application

For processing metal structures
Enamel PF FERROCOLOR SHIP – ready-to-use glossy and semi-matte weather-resistant alkyd enamel is designed for painting metal, wood and other surfaces exposed to atmospheric influences, as well as for finishing works inside residential and industrial premises.

Method of application

PF FERROCOLOR ship enamel is applied by spray, brush, roller
The work must be carried out in ventilated areas using personal protective equipment for the skin, respiratory organs, eyes and face.

The preparation of the working composition consists in thorough mixing. If necessary, it is allowed to add a solvent (P4, xylene or white spirit) in an amount of no more than 20%. The working composition not used during the shift should be filled with a small amount of solvent and tightly closed with a factory lid to prevent moisture ingress, gel formation and increased viscosity during storage.

The material can be applied at an air temperature from +5 °C to +35 °C and a relative humidity of up to 85%. It is not allowed to be applied on a wet or wet surface. The material should be applied in a uniform layer with a thickness of 30 to 80 microns, depending on the coating system used. The material is applied in 1-2 layers. The holding time before applying the second layer at a temperature of (20 ± 5) ° C should be at least 8 hours, but not more than 2 days. The thickness of a single–layer coating (on a dry layer) is no more than 30 microns. Approximate consumption rates per layer: from 80 g/m2.

For delivery issues, contact the sales department:
+7 (903) 885-79-76, +7 (910) 030-16-79

E-mail:
Sale@ferropolymer.ru